Search results

My engine oil dipstick has melted inside the engine block. Has anyone experienced this problem? What is the best way to remove it without taking the engine out?

Has anyone experienced creeping track motors and a free-swinging slew on a Volvo EC220DL excavator? The tracks take time to lock after traveling, and the slew sometimes rotates slightly after the lockout lever is activated.

I'm looking for parts for a Clark R28000 5-speed scraper and haven't had any luck finding them in Australia. Does anyone know a supplier, or have a complete scraper available for wrecking and parts?

Looking at a **Volvo L45G** with a failed transmission. The machine is $25K, but repairs could cost more. Has anyone fixed one, and was it worth it?

My Bobcat 334 excavator runs fine when cold, but once the hydraulic system reaches operating temperature, using the hydraulics makes the engine want to stall. Has anyone experienced this problem? What should I check first?

If your Komatsu PC200LC-6 drives straight but has trouble turning, check the hydraulic system, travel motor, and controls. Finding the problem early can help keep your excavator working properly.

I swapped the plugs, checked the wiring, and repaired a bad wire, but the error is still there. Has anyone had this problem before? What should I check next?

I'm new to owning excavators and could use some advice. My JD 225C LC stays at high idle even when I turn the dial to idle. The auto idle light is green, but it doesn't lower the RPM. The only time the RPM drops is when I turn the key off-it goes down to about 200 RPM, then goes back up. Has...

I recently removed the transmission due to excessive input shaft endplay. After tearing it down, the gears and bearings all appear to be in good condition. The only issue I found is wear on the first clutch pack plate, where the input shaft gear appears to have been rubbing or chewing into the...

The engine runs, but any boom, bucket, stick, or travel function stalls it, while the thumb still works. Where would you start troubleshooting?

I am getting ready to service the cooling system on my 1988 Caterpillar 953 and would like to clean the radiator while I'm at it. Does anyone have a recommended radiator cleaner that works well on these machines?

I am trying to diagnose a CAT 305CR excavator that suddenly lost all hydraulic power while the engine still runs perfectly. The machine has around 7,500 hours and was only doing light blade work when the hydraulics completely stopped working. No burst hoses, no overheating, and no warning signs...

I'm working on the driveline of a Caterpillar 615 and the U-joints are completely worn out The problem is the driveline between the engine and transmission does not look like it has enough room to come out easily. From what I can see, it almost looks like the transmission may need to be moved or...

I've been checking out equipment on GovPlanet, and I'm curious about their product listings. Are the inspection reports and photos actually accurate? Or do issues still show up after you get the machine? Just trying to know how much I can trust the listings before bidding

We've already replaced the injector with a new OEM/Bosch unit, but the machine is still in derate and showing code w015. We also confirmed that def is reaching the injector. At this point, we're not sure what to check next.

Uptime is everything. When your Tadano GR-500XL throws an AML-C code, follow this fast-track guide to get back to the lift. 1. Identify the Code Check the display for a 4-digit code. Most issues (like Error 2022) involve a mismatch between the crane's physical setup and the computer's settings...

I'm currently using a Cat 322 for some precision lifting, specifically picking heavy transformers off trailers. I've been studying the official load tables pretty closely. The manual says not to exceed 87% for hydraulic limits and 75% for tipping limits. However, my bucket alone weighs about...

I'm planning to move a piece of equipment soon (likely an excavator or maybe a mid-size dozer), and I keep seeing Veritread come up when searching for heavy equipment transport services. From what I understand, it works like a marketplace where carriers bid on your load, but I'm still a bit...

What usually causes it and what should I check first?

I'm trying to track down scarifier wedges for an old 1954 CAT 12 motor grader, and I'm starting to wonder if these parts are still available anywhere. This machine is still in working condition, but the scarifier setup is getting worn and I'd like to replace the wedges before it bceomes a bigger...